RF Safety


        Radio on FacebookJoin us on Facebook

The broader category is the non-contact hazard. Here all areas where hazards may exist that do not require physical contact with the tower are examined. Non-contact hazards do not typically in themselves result in burns, although excitation of metallic clothing, jewelry and tools by high-intensity fields can result in material heating. The non-contact hazards tend to relate more to tissue heating and their effects. Some of these effects are not fully understood yet, and may not significantly manifest themselves for many years after exposure.

The exposure limits under this second category are divided into two conditions: uncontrolled environment condition and controlled environment condition. The uncontrolled condition relates to exposure by the general public, or to those areas where you have no control over the access or exposure of persons residing, working or traversing. The maximum permissible power density in such areas is lower by a factor of five than in the controlled environment. As part of the application process, the FCC requires all facilities to demonstrate compliance with the uncontrolled environment condition at ground level, unless it can be satisfactorily demonstrated that areas where the predicted power density exceeds this limit qualify as a controlled environment.

In the controlled environment, the facility has the ability to control the exposure of personnel who are known to be cognizant of the hazards of RF and the implementation of safety procedures. Because of these factors, a higher power density limit is permitted. If work is necessary in areas where these limits are generally exceeded, additional action must be taken, such as the use of RF suits, reduction in power or cessation of operation.

RF suits, while useful in some instances, should never be considered a panacea. While they can attenuate the RF inside to certain levels, tears, rips or other integrity problems with the suit render them unusable. Their initial cost can be prohibitive, and for most stations it usually is more cost effective to build in some downtime rather than make the investment.

Personal radiation monitors, while useful, can be costly to keep calibrated. They can also provide a false sense of security that can simply be eliminated with lock-out/tag-out. Rendering an antenna inoperable through this methodology leaves absolutely no question as to whether it is causing a problem in its vicinity. This ultimately is the best solution to any RF safety concern, and should be part of the implementation of any program.

What's your sign?

Any RF safety plan must include appropriate signage. There are three different types of signs with differing color schemes approved for FCC compliance. Blue signs represent areas where the uncontrolled environment condition may be exceeded, yellow where the controlled environment condition may be exceeded and orange where the controlled environment condition is exceeded. The signs demarcate boundaries between the varying levels. Posting multiple different colored signs at one location is inappropriate and confusing. A sufficient number of signs should be posted so as to be visible from multiple different vantage points at the site.

There are multiple ways to establish the appropriate boundary locations. For FM-only sites, the FCC's FM Model software can predict where the peak power density will occur. The equations in OET Bulletin 65 along with simple trigonometric identities can also be used. For more conservative results, assume the relative field in the vertical plane is 1.0 at all elevations when using the equations.

Finally a survey of the site could be performed. A survey, with a high density of measurement locations properly mapped will provide the best graphical illustration of the situation. Prior to the survey, however, ensure your consultant has fully studied the specific antennas and geometries to ensure appropriate measurement locations are not missed.

While an RF safety plan can be as simple as a de-energize/lock-out/tag-out plan or as complex as various combinations of antenna changes, the importance of crafting, using, and maintaining such a plan cannot be emphasized enough. Although accidents may still occur, those accidents will tend to be viewed as such, and not as willful negligence.


Ruck is a senior engineer with D.L. Markley and Associates, Peoria, IL.




Acceptable Use Policy
blog comments powered by Disqus

[an error occurred while processing this directive]

Today in Radio History

Milestones From Radio's Past

The history of radio broadcasting extends beyond the work of a few famous inventors.

Digital Edition

Each Issue as a Digital Edition

Read each issue online in our Digital Edition Format in your Web browser.

EAS Information More on EAS

NWS XML/Atom Feed for CAP Messages

The feed provides feeds for all US states and territories.

Wallpaper Calendar

Radio 2014 Calendar Wallpaper

Need a calendar for your computer desktop? Use one of ours.

The Wire

A virtual press conference

Information from manufacturers and associations about industry news, products, technology and business announcements.

Join Us Facebook Twitter YouTube LinkedIn
Radio magazine cover

Current Issue

Northern Community Radio Expands: An Engineer's Perspective

When Northern Community Radio set out to build a new community radio station in rural northern Minnesota 38 years ago, naysayers said that it would be broadcasting “only to a bunch of gophers

Browse Back Issues

[an error occurred while processing this directive]