Most Popular Articles
Field Report: Thermo Bond Buildings
Last year I found myself in need of a new transmitter building. As most projects go, I was already behind schedule because of some siting issues. To make matters worse, this was a new and undeveloped site located roughly 30 driving miles outside the city of Gillette, WY, which was at the time going through a bit of a boom. Of the half dozen contractors I originally called, only two even bothered to return my calls and once they heard details they also turned down the job. I was in a bad situation. I had never really given serious consideration to a pre-fab building. All those I had seen before had been relatively small structures, and they all seemed pretty similar, like they were all made from the same cookie-cutter design. I needed a big, complicated building, one capable of holding two Harris HT-30s, a combiner and all the associated equipment. Definitely a unique structure.
But quoting a Charlie Daniels song, “I was in a bind, I was way behind and I was willin' to make a deal.” So I called Chuck McKeever at Thermo Bond. I had run into him the year before at the NAB Show and I figured the least I could do is see what he could provide, when he could get it, and what it would cost. After a few minutes on the phone and a couple of exchanged emails, I faxed him a very crude drawing of the building I had in mind. This drawing was just one step over something you might pencil out on a bar napkin, but it did include placement of the two transmitters and the combiner. Beyond that it was a pretty blank slate.
|Performance at a glance|
Single and multiple room shelters
Wired to custom needs
Insulated steel doors
Aggregate exterior finish
Water and air tight
Bullet resistance options available
A week later I had a rough set of blue prints, a very reasonable price and a delivery date. As the project moved forward, we made some minor tweaks, but Thermo Bond basically worked from the original drawing and the pre-installation instructions provided by Harris. Thermo Bond took care of designing, sizing and locating all of the electrical drops. It placed AC units and HVAC venting and fans. Over the course of a few weeks my cruddy little drawing had become a stamped set of blue prints for the local planning, building and zoning committee, which was another huge time saver. The only time I had to have an inspector on site was to verify that the pad was constructed per the drawing and once more for the final electrical service connection. The building and all of its contents came pre-inspected by Wyoming licensed inspectors.
Up until now, I still hadn't seen the building, so I was pretty excited when the truck driver called. The next morning I met him as he exited the interstate and I guided him to the site where we already had a crane standing by.
An hour and a half later the building was on the pad and I got my first look inside. I was impressed. Not only was everything exactly as we had planned, but the building was bright, well-lit and even included a few extras, like hi/lo temp, loss of power, fire, smoke and intrusion alarms. It was pretty obvious that Thermo Bond didn't cut any corners. All materials were high quality and workmanship was unsurpassed. A week later we slid the two new transmitters onto the floor, under the pre-installed power drops. Everything was exactly where it was supposed to be.
Electrical distribution panels were neatly laid out, well marked and for once I didn't have to explain to an electrician why I wanted separate fused disconnects instead of breakers. Every breaker in the panel was marked, as were all switches, outlets and service connections.
Acceptable Use Policy blog comments powered by Disqus
[an error occurred while processing this directive]
Today in Radio History
The history of radio broadcasting extends beyond the work of a few famous inventors.
EAS Information More on EAS
The feed provides feeds for all US states and territories.
Need a calendar for your computer desktop? Use one of ours.
Information from manufacturers and associations about industry news, products, technology and business announcements.
When building its new broadcast production vehicle, MRN applied lessons learned from the past.
Browse Back Issues[an error occurred while processing this directive]
Also in the April Issue
- Update on Transmitters
- On-air Missteps to Avoid
- Tower Lease Renegotiation
- New Products
- Applied Technology: Streaming with the MPEG HE-AAC Audio Codec
- Side by Side: Studio Furniture
- Practical Use: Circulators and Isolators