Most Popular Articles
Connecting studio facilities and transmitters
32 Avenue of the Americas is home to one of several large Carrier Hotels in New York City, and as such was an advantageous location for our endeavor. “The Hub” as it is known has more than 50 tenants, including AT&T, Verizon, Qwest, XO, and Global Crossing. Obviously this was an advantage to us in choosing a carrier for our communications needs in and out of the building. The Hub itself is on the 24
Director of Engineering Josh Hadden decided there would be no wirelines to the 24
Each of the five stations makes use of a Harris/Intraplex DACS 9560 cross-connect as the primary STL. In this way, one encoder board (in this case a PT353) can have its encoded output (timeslots 1 through 23) “copied” and also sent out via an additional port on the DACS. The first port on the 9560 is used to communicate with our main transmitter site at the ESB; the copied port is sent to our backup site at 4 Times Square. A separate DACS frame is used to handle all the five stations remote controls.
The T1 links from the DACS, meant for the ESB, are connected to an Adtran MX2800 DS3 mux/demux. The DS3 link from this particular MX2800 is connected to the Opti-6100 for the west riser, and thereafter connected to the 24th floor. The T1 links from the DACS meant for Times Square are sent to a separate MX2800, and thereafter connected to the 24th floor via the Opti-6100 assigned to the east-riser.
Each MX2800 mulitplexes 28 separate T1s though; and if you were counting, you only got to six. Each transmitter site also has a separate network (each of which is really just a separate subnet of the 10.xxx.xxx.xxx network used inside the Clear Channel WAN). Quite a bit of data makes its way up to the ESB: RDS, MPS PAD, and SPS PAD for WLTW (Lite FM), WHTZ (Z100), WAXQ (Q104-3) and WWPR (Power 105.1). The entire HD Radio data stream for WKTU gets to the ESB over this same network link. As you would expect there are many computer workstations located at the ESB as well — scattered throughout our four different transmitter rooms on three floors of the Empire State Building (ESB). (Data requirements for our 4 Times Square transmitter site are lighter.) The link for each of the two transmitter sites' networks consists of 16 T1s bundled in to a single PPP connection by way of two sets of Adtran 5305 Routers (one set for the ESB and one set for 4 Times Square).
The actual physical links between 32 Avenue of the Americas and the two transmitter sites are T3s provided by AT&T on the 32 Avenue of the Americas, and Verizon at each of the transmitter site ends. (Obviously they meet up at one of the various central offices located in Manhattan.)
The Evertz system I mentioned earlier also consists of shelves in to which specific-function modules are added. Like the Adtran system, the Evertz shelf in our MCR is connected to its complement on the 24
So even though we use two separate risers in the building for our fiber runs to the 24
32 A/A is only about 2.5 miles south of the ESB (and just slightly farther from 4 Times Square) and since our off-air receive antenna is on top of the building (525' AGL) you would expect that the receive signal level is quite good — and you'd be right. Using a single Scala CLFM we get about -10dBm per carrier from each of the 18 FM signals at the ESB. In order to meet our fiber only system requirement, we used another Evertz module pair — the 7707 IFTA and IFRA. This system accepts RF over a wide bandwidth, converts it to light, runs it over a fiber, and puts RF back out the other end. In this manner we're able to get RF from our analog and HD transmitters from the receive antenna on the roof, and to the MCR. Finally, we make use of a set of 7707GPS modules to get our GPS signals from the roof to MCR, where two Evertz 5600 MSC units feed a 5600ACO, providing redundancy in the generation of all the clock signals we need throughout the facility.
The Clear Channel consolidation project in New York is arguably one of the largest and most complex projects ever taken on by the company. The major design factors for all inbound and outbound communication systems are the number of sites involved and a high level of redundancy for each. A tremendous amount of time and energy went in to the design and implementation of the systems described, and we anticipate the results will benefit the stations for years to come.
Irwin is chief engineer of WKTU, New York.
Acceptable Use Policy blog comments powered by Disqus
[an error occurred while processing this directive]
Today in Radio History
The history of radio broadcasting extends beyond the work of a few famous inventors.
EAS Information More on EAS
The feed provides feeds for all US states and territories.
Need a calendar for your computer desktop? Use one of ours.
Information from manufacturers and associations about industry news, products, technology and business announcements.
When building its new broadcast production vehicle, MRN applied lessons learned from the past.
Browse Back Issues[an error occurred while processing this directive]
Also in the April Issue
- Update on Transmitters
- On-air Missteps to Avoid
- Tower Lease Renegotiation
- New Products
- Applied Technology: Streaming with the MPEG HE-AAC Audio Codec
- Side by Side: Studio Furniture
- Practical Use: Circulators and Isolators