Field Report: Airtools 6100
At KCUR we produce two one-hour live call-in talk shows every weekday. When I started in January 2004, I was surprised to find that they operated with no profanity delay. I immediately suggested that we purchase and install one. Because we are an NPR station and had operated for nearly 20 years with no delay, it was thought that we weren't in real danger. Then the famous Superbowl half-time show occurred and people realized that the FCC fines could put a serious dent in our budget. Then my suggestion was taken seriously. We tried a software-based option. It worked OK, but was problematic in that it depended heavily on the stability of the PC hardware. We started looking for alternatives. There were two products available that met our requirements. We needed to keep our air chain all digital. We selected the Airtools 6100.
It is a 1RU device with an IEC ac cord. There is no wall-wart.
The front panel interface is easy and I would say almost intuitive. The alphanumeric and bar graph display works with three buttons and a knob. The three buttons are labeled Previous, Next and Home. These navigate through the circular, single-level menu. When the Home button is pressed this display reverts to a bar graph of the audio passing through the unit. The knob selects the various choices for each menu entry. There is a numeric display of the delay time. In addition, on the front panel are the familiar switches for Exit, Start, Cough and Dump. When any of these functions are engaged on the front panel or remotely via the DB-25 remote control and indicators connector, the appropriate switch flashes. A bypass switch is the last switch on the front panel. This is a mechanical bypass relay in case of disaster.
|Performance at a glance|
As many as 40 seconds of delay
User-selectable delay algorithms
Automation control interface
AES3 and analog I/O
The rear panel is a busy place because of the 1RU form factor. Three TC89 time code BNC connectors, a DB-9 RS-232, an RS-485, the previously mentioned remote control and indicators DB-25, an automation DB-25, a BNC word cock in connector and six XLR connectors for stereo audio in and out and AES3 in and out are all on the rear panel.
The 6100 was easy to install and interface with our Enco DAD system. Contact closures from the DAD wired directly to the remote control and indicators connector. This allows the delay to be entered on a time basis programmed by the DAD system. We enter the delay 10 minutes before the talk show starts. This allows the algorithm to have a full six-seconds delay by the time the show starts. The 6100 can be set for any delay from zero to 40 seconds in 0.1 second increments. We selected the Gap Detect and Catch Up algorithm, which for our format was the most seamless. The choices are Gap Detect, Gap Detect and Catch Up, Continuous, and Pitch Shift. The best way to select the algorithm is in the air chain. We used the AES3 inputs and outputs but also wired the analog input as a backup.
There are four user programmable SPDT form C relay contacts available. For complete control, there is a description of the functions available, protocols and syntax in Appendix D of the users guide. Because this has an embedded processor this is one powerful unit.
|Input Source||analog or AES/EBU|
|Nominal Input Level||-10dBu, +0dBu, +4dBu, +8dBu|
|Nominal Output Level||-10dBu, +0dBu, +4dBu, +8dBu|
|Digital Input Sync||internal 48Hz, word clock, AES/EBU|
|Delay Time||0.0 to 40.0 seconds (in 0.1 second increments)|
|Dump Length||fifth, fourth, third, half, whole|
|Algorithm||gap detect, gap detect and catch up, continuous, pitch shift|
|Delay Ratio||10:1 to 40:1 *|
|Bar Graph Mode||pre-delay, post-delay|
|Automation Trim||±300ms from Early to Late in 30ms increments|
|Rear Serial Port||RS-232 (DB-9) or RS-485 (3-pin euro)|
|Serial Port Baud||9600, 19200, 38400|
|Unit Number ID||1 through 255|
|*- ratio controls the balance of delay build/exit speed vs. overall audio quality|
Things that must be said
This is a professional unit and it has XLR type balanced connectors. It can be wired and the levels set for unbalanced wiring. It also uses AES3 connections. There is no provision for S/PDIF digital audio. The input source must be selected but the AES3 and analog outputs are always active. We used the analog output as the source to drive our mono analog line that backs up our T1.
With all the setup and connections, I cannot imagine a situation where it could not be configured. At KCUR it was easy to install and configure. Earlier versions of the firmware had some problems, but the latest version seems to be bug free.
There is an additional use for the unit. It can be used as the audio delay for HD Radio for the air chain. Because the delay can be set in 0.1 second increments, the delay can be precisely timed for the required HD Radio delay. This eliminates the need to route the AES3 audio through the HD Radio exciter.
We view this device as insurance. We hope that we never need to use it but we know that it is there when we need it.
Cross is the chief engineer of KCUR-FM, Kansas City.
Editor's note: Field Reports are an exclusive Radio magazine feature for radio broadcasters. Each report is prepared by well-qualified staff at a radio station, production facility or consulting company.
These reports are performed by the industry, for the industry. Manufacturer support is limited to providing loan equipment and to aiding the author if requested.
It is the responsibility of Radio magazine to publish the results of any device tested, positive or negative. No report should be considered an endorsement or disapproval by Radio magazine.
Acceptable Use Policy blog comments powered by Disqus
[an error occurred while processing this directive]
Today in Radio History
The history of radio broadcasting extends beyond the work of a few famous inventors.
EAS Information More on EAS
The feed provides feeds for all US states and territories.
Need a calendar for your computer desktop? Use one of ours.
Information from manufacturers and associations about industry news, products, technology and business announcements.
This high-visibility and high-traffic area got the full acoustic treatment.
Browse Back Issues[an error occurred while processing this directive]
Also in the May Issue
- Remote Access and Site Connectivity: Wireless
- Standards of FM Allocation and Interference
- Side by Side: Mic Processors
- Field Report: Deva Broadcast DB4004
- Field Report: APT WorldCast Systems Horizon NextGen
- New Products
- 20 Years of Radio magazine: May 1994