Digital Audio Testing
Getting your bits in a row
Some form of organization is needed so the receiver can reassemble and identify the assorted bits of information contained in a digital audio data stream. Organization involves assembling the data into blocks. Each block consists of 192 frames of audio. Each of the 192 frames can be divided into two sub- frames for two-channel audio. Each frame is produced at the digital audio sampling rate so each frame contains one digital value. In a 48kHz audio sampling rate, each frame is 20.833µs (microsecond) with each frame lasting 4ms (millisecond).
Each frame can carry two audio channels. In a two-channel mode, the samples from both channels are transmitted in consecutive sub-frames. Channel 1 is in sub-frame A and channel 2 is in sub-frame B.
In addition to the digital audio word data bits, each sub-frame contains additional data. Each sub-frame consists of 32 bits, which includes 20 or 24 bits of audio word data bits and eight bits of additional data. Each sub-frame includes bits for preamble or sync data, auxiliary data, audio data word bits, validity (V), user (U), channel status (C ) and parity (P) data bits. Considering that each sub-frame consists of 32 × 2 bits, occurring in 20.833µs (FS = 48kHz), the bit rate increases to 1,536,024 × 2 = 3,072,048 bits per second.
The first four bits of each sub-frame consist of four preamble bits or sync bits. These bits identify the start of a new audio block and each sub-frame. A “Z” sync bit arrangement marks the start of the first frame in the 192 frame block. The sync word “Y” indicates the start of every B sub-frame. The sync word “X” indicates the start of all remaining frames. The sync bit arrangement is used by a digital audio receiver to identify the start of the audio blocks and sub-frames.
Analyzing frequency accuracy
At the heart of any digital system is a clock. This is a crystal oscillator or voltage-controlled crystal oscillator circuit. The oscillator output determines the resulting audio sample rate and audio data rate. A perfect circuit would be exactly the desired frequency and each cycle of the clock waveform would be identical in duration or time.
The clock isn't a perfect circuit, as the crystal is not perfectly accurate. Crystals are rated in accuracy described by a parts-per-million (PPM) rating. This indicates the maximum number of cycles the frequency may deviate for every one million cycles or hertz. A typical crystal rating is ±20 PPM. If the crystal frequency was 1,000,000Hz (1MHz), the generated frequency would be within ±20Hz (1,000,020 to 999,980). The 20 PPM rating is additive. A crystal of 2,000,000Hz could deviate ±40Hz, while a 3,000,000Hz crystal could deviate ±60Hz and so on.
In digital audio terms, a crystal frequency of 12,288,000Hz is commonly selected. This is 256x the ideal sample rate of 48,000Hz. A 20 PPM error at this frequency calculates to an error in frequency of ±246Hz. Because this is a maximum error, one would expect typical operational errors in PPM or Hz to be much less.
In digital audio systems, some frequency error is tolerable
because the clock frequency is imbedded into the audio data stream and
used to recreate a matching clock frequency by subsequent digital audio
equipment. However, good maintenance and troubleshooting practices
should include a frequency measurement of the digital audio signal
including the sample rate frequency (F
When multiple AES digital audio signals are created by separate clocks, differences in clock frequencies and sync timing exist. These differences present challenges to digital audio equipment designed to switch between or process multiple inputs. To produce multiple AES digital audio signals at the same frequency and timing, master clocks or digital audio reference signals (DARS) can be used to synchronize oscillators and sync timing.
Discussion about clock frequency and timing errors would not be complete without talking about jitter. With a perfect clock square-wave each subsequent clock cycle would be identical in time, with positive and negative parts of the cycles the same duration. The clock would be a symmetrical square-wave with each of its transitions occurring in exact time increments from the previous transition.
Again, the clock is not perfect. Clock cycles may fluctuate in time with cycles being slightly shorter or longer than previous cycles. Clock positive and negative times may be slightly longer or shorter causing transitions to occur at slightly different intervals in time. These variations are called jitter.
In a digital system, it's all about timing. Consider how these timing variations can cause audio signal degradation. For example, consider a perfect jitter-free clock digitally sampling a linear rising waveform during the analog to digital conversion as shown in Figure 5. If the waveform is reconstructed by a digital-to-analog converter containing some clock jitter, the linear rising voltage is no longer linear. The digital values correctly indicate the audio level as it was sampled, but because the levels are incorrectly placed in time, the resulting waveform is distorted by the jitter component.
Jitter occurs in a digital audio system at the transmitter from the non-perfect clock or crystal oscillator circuit. This is commonly called transmitter or sampling jitter. The digital audio signal is also adversely affected on the interface transmission line, which contributes to jitter. This is commonly called interface jitter. These jitter elements are cumulative as the digital audio is transmitted and moves through a transmission line to a receiver.
Digital audio embeds the clock signal and sync transitions within the serial digital audio data stream. It is up to the receiver to regenerate an oscillator locked to the incoming digital audio. As in any digital system, the data transitions from high to low have crossover points. These transition points are used to lock and correct the oscillator frequency in the receiver. Influences on these transition points contribute to jitter within the receiver's clock.
One contributor of jitter is the data transmission line, better known as the connecting cable. The cable's capacity and frequency response characteristics can cause waveform shaping and slight DC balance shifts to the digital audio waveform. This causes slight delays or advances of the transition points along the digital waveform input to the receiver. This is interpreted at the receiver as jitter. Noise can also be induced into the transmission line, which further can shift the crossover points.
Measuring jitter is an important step to ensuring a quality digital audio signal. Jitter may be measured by an AES digital audio analyzer. Typical jitter measurements are displayed as small time errors and expressed in nano or pico seconds. Jitter errors are commonly expressed as an average RMS value to reduce the measurement effects of randomly occurring peak jitter errors. The AES/EBU standard specifies that jitter be less than ±20nS. However, it is desirable to minimize jitter to much lower levels to optimize digital sound reproduction.
Kropuenske is an application engineer with Sencore.
Acceptable Use Policy blog comments powered by Disqus
[an error occurred while processing this directive]
Today in Radio History
The history of radio broadcasting extends beyond the work of a few famous inventors.
EAS Information More on EAS
The feed provides feeds for all US states and territories.
Need a calendar for your computer desktop? Use one of ours.
Information from manufacturers and associations about industry news, products, technology and business announcements.
Staying on-air is priority #1, but 100 percent redundancy comes at a cost.
Browse Back Issues[an error occurred while processing this directive]
Also in the November Issue
- Music is Everywhere at WTMD
- FCC Looks to Update RF Exposure Rules
- Government Shutdown Causes FCC Delays
- Applied Technology: Wheatstone baseband192
- Side by Side: Video Cameras
- Exploring More from Google Earth
- The History of W9BSP