Most Popular Articles
The Pick Hits of the 2008 NAB Show
Vector impedance analyzer
Power Aim 120: The Power Aim 120 features high-resolution plots of all selected parameters, including R, X, SWR, reflection coefficient, return loss, load impedance magnitude and load impedance phase angle. A VSWR sideband ratio tool will quickly calculate the sideband VSWR ratio. Fast and accurate measurements allow for quick tune-ups and documentation via real-time PC data plotting over large ranges of frequency and impedance. Variable scaling of the frequency range and the parameter magnitude limits for clear data collection and read-outs both during a test session and afterward in off-line analysis. Fast sweeps and easy multiple plot and data point measurement saving for self-documentation and export to Microsoft Excel for further plotting and analysis. Data curve averaging and smoothing capabilities are available to reduce test measurement noise. A scan overlay feature provides rapid detection of system changes and the effects of adjustments, and a recycle mode offers continuous scan updates during adjustments.
- Performs all the function of a network analyzer at a fraction of the cost.
- It covers the AM and FM bands, so it's even more useful.
Licensed RF STL
IP-Connect/IPC 100: IP-Connect offers broadcasters new options for Ethernet-based, bi-directional, multichannel audio and broadband data connectivity for mission-critical transmission applications. IP-Connect's IPC-100 data link is the first in a new series of programmable, scalable and spectrally efficient 11, 18 and 23GHz band radios. These units are fully configurable due to their single-chip ASIC modem featuring integrated FEC with selectable coding rates allowing transport data rates from 8 to 32 T1s, 2×DS3, 50 to 250Mb/s Ethernet, or up to 2×STM1 + 2×T1. Mixed data rates and formats can also be supported allowing the IPC-100 to act as a transparent data pipe for any network facility. Due to the IPC-100's frequency and bandwidth agility it offers licensed applications for program audio last-mile studio-to-transmitter links in the 18GHz band. Hardware configuration is implemented on the IDU/ODU design. Deployment of the IP-Connect IPC-100 is made via a single-run coax connection from the indoor unit to the outdoor unit/microwave antenna.
- Licensing use for 18GHz makes this practical for long-time use.
- Lots of IP and data capacity, and the modems are configurable.
All-in-one FM transmitter
Digiplexer246/Next FM: The Digiplexer246/Next FM is the first all-in-one FM transmitter that includes digital audio processors, a stereo encoder plus additional innovative features such as an RDS encoder, embedded audio backup, I/O remote control and TCP/IP connectivity. Ecreso's engineers have partnered with the Sound4 audio gurus to incorporate a high quality audio processor that is based on a powerful DSP hardware platform. The Digiplexer246/Next FM operates at a sampling frequency of 192kHz for the main audio processing and 1.5MHz for the final limiter.
- The built-in 80GB hard drive will fill lots of needs.
- With everything built-in, it's a Swiss Army knife of transmitter devices.
Ethernet audio system
E2: The E2 System is designed to interface with Wheatstone's existing line of E-Series control surfaces including the new Evolution 4 control surface. The flexible E2 system is comprised of linkable units or squares that communicate with one another via a single CAT-5E/6 cable connected to standard layer 3 Ethernet switches. The E2 Digital Engine handles all of the mixes from the E-Series surfaces while housing the DSP power and managing the distribution of PGM, AUX, and mix-minus buses throughout the system. 12 Universal Logic ports are encased in the single rack unit which is equipped with front-panel access to real-time control features such as IP setting, up time, network traffic and logic status. Web/PC software user interfaces provide remote access and control.
- It's another IP audio device, but it adds features and options that were not available before.
- Splitting a stereo input into two mono inputs is a more efficient use of resources.
Multi-stream networked audio processor
Omnia.8X: With algorithms modeled after the Omnia.3net, this processor provides eight discrete three-band stereo audio processors in a single, networked box. Its architecture works ahead of any bit-reduced audio coder to reduce artifacts and improve the sound audio destined for HD Radio, Internet and satellite broadcasting. Use it to process headphone feeds where off-air monitoring is not possible; as multiband level control for remote codecs or on-air telephone systems; to process and send multiple audio streams from a single studio complex to multiple transmitter sites; or on-demand for in-studio musical performances or commercial production applications. The processor uses the Livewire standard over Ethernet.
- I can use this for multiple in-house headphone processing or online stream processing.
- The configuration of variable-band processing makes this a flexible tool.
Acceptable Use Policy blog comments powered by Disqus
[an error occurred while processing this directive]
Today in Radio History
The history of radio broadcasting extends beyond the work of a few famous inventors.
Read each issue online in our Digital Edition Format in your Web browser.
EAS Information More on EAS
The feed provides feeds for all US states and territories.
Need a calendar for your computer desktop? Use one of ours.
Information from manufacturers and associations about industry news, products, technology and business announcements.
When Northern Community Radio set out to build a new community radio station in rural northern Minnesota 38 years ago, naysayers said that it would be broadcasting “only to a bunch of gophers
Browse Back Issues[an error occurred while processing this directive]
Also in the July Issue
- Trends in Technology: Robust IP STL
- LPFM on The March
- RF Engineering: Modern Modulation Techniques
- Field Report: Tascam TH-2000 Headphones
- Battery Maintenance: Testing and Charging